JL Audio 10TW1-2 TW1 Series 10" 300W RMS (600W Peak Power Handling) 2 Ohms, Shallow-Mount Component Car Subwoofer
We are a JL Audio authorized dealer so you get up-to-date, fully warrantied products. Shipping is free to the lower 48 states on everything you order!
What's Inside?
- • (1) 10" Thin-Line 2-ohm subwoofer
- • Grille (installed)
- • On-line product registration information
- • Owner's Manual
Why Choose JL Audio 10TW1-2 Component Car Subwoofer?
Big Bass, Small Footprint
Maximize your sound without sacrificing space. The low-profile recessed suspension lets the cone reach full excursion with just 0.87" of frontal clearance—even with the grille installed—making it ideal for tight installations. Engineered for big sound from compact enclosures, the shallow mounting depth and exceptional excursion capability deliver smooth, powerful bass. Built to last, the injection-molded, mica-filled polypropylene cone with rubber surround provides durability, moisture resistance, and minimal distortion for crisp, clean audio every time.
Precision Bass, Engineered for Every Space
Experience tight, clean, and articulate bass at any power level with Dynamic Motor Analysis (DMA) optimized design—where proprietary motor, suspension, and cone modeling deliver perfectly linear excursion. The cast-alloy, space-saving frame with flat edges lets you install multiple subwoofers side by side, making it ideal for compact setups without sacrificing performance.
Compact Design, Big American Bass
Engineered for maximum versatility, the 10TW1-2 delivers powerful performance in both sealed and ported enclosures with amplifiers ranging from 75–300 W RMS. Its seriously shallow 4-3/8" mounting depth makes installation in tight spaces effortless. Built in the USA with a cast-alloy frame and innovative “concentric tube” motor structure, this subwoofer minimizes profile without compromising performance—bringing big, clean bass to any setup.
Frequently Asked Questions (FAQ)
- • Will the JL Audio 10TW1-2 fit in a shallow subwoofer box?
Yes, the 10TW1-2 is specifically designed for shallow-mount applications where installation depth is limited. Always use an enclosure that meets JL Audio's recommended internal volume for the best performance.
- • Why does my JL Audio 10TW1-2 have very little bass?
Weak bass is commonly caused by incorrect enclosure size, improper amplifier tuning, or reversed speaker polarity. Verify the wiring and crossover settings before increasing the amplifier gain.
- • What is the recommended power range for this subwoofer?
The 10TW1-2 has a continuous power handling of 300 watts RMS. For optimal performance, we recommend using an amplifier capable of delivering between 75 and 300 watts RMS.
- • Why does it sound distorted at higher volume?
Distortion usually happens because of amplifier clipping, excessive bass boost, or incorrect gain settings. Proper amplifier tuning and clean input signals will help maintain clear bass.
- • Can I install it in a sealed or ported enclosure?
Yes, the subwoofer performs well in both enclosure types when built to JL Audio's specifications. Your preferred sound quality and available space will help determine the best enclosure design.
- • Why is my amplifier going into protection mode with the JL Audio 10TW1-2?
This is often caused by incorrect impedance wiring, poor grounding, or amplifier overheating. Confirm your wiring matches the amplifier's supported load before replacing any equipment.
- • What size amplifier works best with the JL Audio 10TW1-2?
An amplifier that delivers power within JL Audio's recommended RMS rating will provide the best results. Choosing clean power is more important than simply selecting the highest wattage available.
- • Can I use a different wall thickness for my custom enclosure?
The recommended specifications assume a wall thickness of 0.75 inches (19 mm). If you use thinner material, such as 0.625 inches (16 mm), you must compensate by slightly adjusting the external dimensions to maintain the correct internal volume.
- • Can I use two JL Audio 10TW1-2 subwoofers in the same system?
Yes, many users install dual 10TW1-2 subwoofers for increased bass output and better overall performance. Make sure your amplifier can support the combined impedance and power requirements.
- • How much frontal clearance does the subwoofer need?
Thanks to its recessed suspension design, this subwoofer requires only 0.87 inches (22 mm) of frontal clearance. This allows you to install the driver in confined areas without worrying about the cone hitting the grille during excursion.
Learn how to wire subwoofers
- Diameter : 10 Inch
- Sensitivity : 82.5 dB
- Impedance : 2 Ohm
- Frequency Response : 26-200 Hz
- Peak Power Handling : 600 Watts
- Shallow Mount : Yes Inch
- Number of Voice Coils : Single
- Suggested Sealed Box Volume : 0.35 Cubic ft.
- Suggested Ported Box Volume : 0.625 Cubic ft.
- RMS Power Handling : 300 Watts
Features:
- Recessed Suspension: Low-profile design allows most forward cone excursion to occur within the frame, requiring only 0.87" of frontal clearance (even with grille installed) for more efficient space use.
- Engineered for Big Sound from a Small Enclosure: Shallow mounting depth and outstanding excursion capability deliver smooth, powerful bass from compact enclosures.
- Polypropylene Cone Technology: Injection-molded, mica-filled polypropylene cone with rubber surround ensures durability, moisture resistance, and minimal distortion.
- Dynamic Motor Analysis (DMA) Optimized Design: Proprietary motor, suspension, and cone modeling achieve linear excursion with tight, clean, and articulate bass at all power levels.
- Space-Saving Frame Design: Cast-alloy frame with flat edges allows tight grouping for side-by-side installations.
- Powerfully Adaptable: Works in sealed or ported enclosures with amplifiers in the 75–300 W RMS range (for 10- and 12-inch versions).
- Seriously Shallow: 10TW1-2 subwoofer features a 4-3/8" mounting depth, ideal for tight spaces.
- Unique Construction, Built in the USA: Cast-alloy frame with compressed “concentric tube” motor structure minimizes profile without sacrificing performance.
Specifications:
- Size: 10-inch
- Impedance: 2 Ohms
- Cone Material: Mica-filled polypropylene
- Surround Material: Rubber
- Basket Material: Cast Alloy
- Grille: Black steel mesh
- Free-Air Use: No
- Dual Voice Coil: No
- Sensitivity: 82.5 dB at 1 watt
- Frequency Response: 26 – 200 Hz
- Max RMS Power Handling: 300 W
- Peak Power Handling: 600 W
- Top Mount Depth: 4 3/8 in
- Bottom Mount Depth: N/A
- Cutout Diameter: 9 1/16 in
- Frame Width: 10.375 in
- Frame Length: 10.375 in
- Vas: 10.31 liters
- Fs: 41.45 Hz
- Qts: 0.649
- Xmax: 10 mm
- Ideal Sealed Box Volume: 0.35 cu. ft
- Minimum Sealed Box Volume: 0.28 cu. ft
- Maximum Sealed Box Volume: 0.54 cu. ft
- Ideal Ported Box Volume: 0.625 cu. ft
- Minimum Ported Box Volume: 0.5 cu. ft
- Maximum Ported Box Volume: 0.87 cu. ft
- UPC: 699440921886
- Weight: 10
- Authorized Internet Dealer
Warranty: 2 Year(s) Warranty.
This item is accompanied by a manufacturer's warranty. If it is found to be defective, it may be returned to OnlineCarstereo.com for repair within 1 year from the original date of purchase with proper return authorization.
Do you own this product?
Write a review!
-
Got this powerful sub, put it in a box I personally built, and with my 300-watt mono amp, it sounds really nice. Doesn't take up too much space in my Tacoma either, unlike my old JL sub.
-
Made my own ported enclosure for the sub and the shallow design of the sub really makes it easier for me to build it. I’m ecstatic after hearing how the sub sounds for the first time even with the less area that it took to setup the box.
-
always been a fan of shallow subs, especially from JL Audio. Good power output. fits in the enclosure I have in my Cherokee. got some clean lows with this sub.
